Plumbing Basics: Before Installing a Bathtub
Call TodayNearly everybody has got their unique notions about Tools You Need to Install a New Bathtub .
Installing a bath tub isn't specifically rocket science, but it does require strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a new one is also a moderately tough job. If the old tub is easily available, the project can relocate easily; if you have to open up a wall surface to get rid of the old bathtub and also place the new bath tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the new one. Make sure you have certified yourself for the work and fit attempting it. Rather than working with a service provider to take control of a halfway-completed project, it is far better to consider employing one prior to you start. Possibilities are you might need a professional plumber to make tube connections.
This write-up will certainly assist you install a new tub in your washroom if you have actually already purchased a brand-new tub as well as do not require to change the setup of your previous supply of water pipes.
Your tools and also product checklist should make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, after that the first thing you should do is detach the supply of water. After doing so, turn on the taps to drain any kind of water staying in the system. The procedure of getting rid of the existing faucets can be fairly troublesome as a result of the limited access that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will come from the pipes. As soon as the supply pipes have actually been gotten rid of, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. When the faucets have been removed, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers remain in location in between the tap as well as the sink. Secure the faucet in place with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The former kind should be connected to the tap ends initially, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Making use of the two wood boards under its feet, position the bath tub in the required position. The wood boards are valuable in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bath tub up until the level checks out level.
To mount taps, fit all-time low of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water and also inspect all joints and new pipework for leaks and also tighten them if necessary. Fill the bath tub and likewise inspect the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub needs to wait until the bath tub has been used at least when as this will certainly resolve it into its final placement.
Planning for the Setup
Firstly, the supporting framework provided with the bathroom must be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to prevent pressure on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to split a rigid seal, creating the water to penetrate the wall between the bathroom and also the tiling, causing problems with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and also cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bath tub with water before sealing, to permit the motion experienced when the bathtub remains in use. The sealer can fracture fairly very early if you do not take into account this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic person who reads on Installing A Bathtub, I imagined sharing that excerpt was worth the trouble. If you please take the opportunity to promote this blog entry if you enjoyed it. Many thanks for your time. Visit again soon.
Emergency plumbing? Choose the best.